蛇纹石矿的开发利用现状及发展趋势

我国拥有丰富的蛇纹石矿资源，其中有许多在近些年已得到较好的开发利用。综述了蛇纹石矿的开发研究现状，指出蛇纹石矿作为耐火材料及Mg、Ni及Pd等有价金属的重要矿物来源，应加强选矿及综合利用方面的研究。     

Isothermal Gas Forming of Mg Alloy AZ31 Sheet

There have been reports on sheet forming of Mg alloy in industry via the punch and die method;this paper is probably the first formal one for studying the sheet formability of AZ31 employing pressurized gas to press the sheet into a female die cavity at various elevated temperatures.The results indicate it is feasible to form a rectangular box via pressurized gas from extruded sheets of 0.5 and 1.7 mm thick.The formed box has 1:2 depth over width ratio,which should be large enough when dealing with realistic industrial sheet forming parts.Presently,forming a sheet of 0.5 mm thick is considered a technical challenge by industry,and it is conquered as demonstrated in this paper.Gas forming technique applied to Mg alloy is unprecedented and shows potential for industrial utilization.     

助催化剂对TiCl_4/MgCl_2催化丙烯高温聚合的影响

研究了助催化剂种类(三甲基铝、三异丁基铝、三正己基铝、三乙基铝和甲基铝氧烷)及其含量对无内、外给电子体的TiCl4/MgCl2催化剂催化丙烯高温(100℃)聚合性能的影响,并用结晶分级分析、示差扫描量热和凝胶渗透色谱等方法分析了所得聚丙烯的结晶熔融行为和微观结构。实验结果表明,聚合温度从70℃升至100℃时,TiCl4/MgCl2催化剂的定向能力基本不变;100℃聚合时,以烷基化能力较弱的三异丁基铝为助催化剂时TiCl4/MgCl2催化剂的活性最高,而采用烷基化能力最强的三甲基铝为助催化剂时TiCl4/MgCl2催化剂的活性最低;100℃聚合时,助催化剂的种类对TiCl4/MgCl2催化剂的定向能力影响很小。     

不同磁场作用对AZ31镁合金的凝固组织的影响

镁合金是具有优越性能的金属材料,镁合金的加工是目前国内外正在深入进行研究的新课题.实验发现在镁合金的凝固过程中施加低频或静态磁场都能细化晶粒,但静磁场得到的细化效果要优于低频交流磁场,同时随磁感应强度的增加,静磁场细化晶粒的效果明显提高;在静磁场条件下晶界共晶体组织的厚度明显减小,同时在晶内出现了大量细小块状化合物,这有利于改善镁合金的综合性能.     

纯镁对碳化硼颗粒的常压浸渗

本文研究了纯镁对不同致密度的碳化硼(B₄C)颗粒基片的常压浸渗性;讨论了镁液对B₄C颗粒聚集体常压浸渗的影响因素;提出了浸渗模型。研究表明,纯镁在氩气保护下,800～850℃温度范围保温30min即可浸渗B₄C颗粒聚集体。浸渗深度和宽度随加热温度升高和保温时间延长而增加;常压浸渗的B₄C_P/Mg复合材料具有很高的硬度,B₄C颗粒在基体中分布较均匀。     

The chloride stress-corrosion cracking behavior of stainless steels under different test methods

Chloride-induced stress-corrosion cracking (SCC) is one of the failure modes of stainless steels. Highly alloyed austenitic stainless steels S32654, S31254, and N08028, and duplex grades S32750 and S31803 possess much improved resistance to SCC compared with S30400 and S31600 steels. With the development of a database, SSData, experimental data collected from calcium chloride tests, autoclave tests, and drop evaporation tests were evaluated. Stress-corrosion cracking data generated by autoclave tests agreed well with the practical service conditions and can be used to discriminate alloys for SCC resistance in sodium chloride solution. Drop evaporation test data can be used in situations where evaporation may occur and cyclic loading may be involved. The SCC resistance of alloys under each method increased with increasing molybdenum equivalent Mo + 0.25Cr + 0.1Ni. For a given alloy, the testing result depends on the stress state and environment; different test methods can give different ranking orders concerning SCC resistance. The performance of duplex stainless steels in a chloride-containing environment at higher temperatures was not as good as expected when dynamic loading was involved.     

Determination of tryptophan in feedstuffs: Comparison of two methods of hydrolysis prior to HPLC analysis

The tryptophan content of nine samples of commercial feed was determined using two procedures (I and II) differing mainly in the hydrolysis conditions used prior to analysis. With I, hydrolysis was performed with 4 M LiOH in the presence of maltodextrin with 5-methyltryptophan used as internal standard at 110°C for 24 h; with II. oxygen-free 1.3 M Ba(OH)₂ was used at 125°C for 16 h. The two procedures gave identical results for a given sample indicating that the corrections for the incomplete recovery of tryptophan 5-methyltryptophan quantitation were satisfactory.     

炼镁还原罐制造技术的现状与发展

介绍了炼镁还原罐制造技术的发展历程和研究现状，分析了未来的发展趋势与发展方向。     

镁合金表面喷铝防腐蚀层的微观组织分析

在AZ91D镁合金表面热喷铝，用以提高其表面的耐腐蚀性能。采用SEM，EPMA等方法对AZ91D表面喷铝扩散层的组织进行了仔细的观察与分析，发现在防腐蚀层上有大量的Mg17Al12相存在，且呈决状及非连续片状分布。经显微硬度测定，喷铝层硬度较镁合金基体高；腐蚀后这种相凸出于基体，比镁合金基体有较好的耐腐蚀性能。     

Direct electroless Ni-P deposition on AM50 magnesium alloy from sulfate bath

A bright electroless Ni-P deposition on AM50 magnesium alloy in a sulfate plating bath was proposed by using direct plating process with non-chromate pretreatment. The electroless Ni-P plating on AM50 magnesium alloy has an admirable appearance and good adhesion. The results indicate that the electroless Ni-P deposition with non-chromate pretreatment has better adhesion than that of zinc immersion coating. Anodic polarization curves indicate that the electroless Ni-P deposition obtained from the sulfate bath has similar corrosion-resistance to that obtained from basic nickel carbonate bath. The deposition process generates less pollutant by a non-chromate plating bath and is suitable for the magnesium alloys manufacture because of its low cost. The hardness of the electroless Ni-P plated AM50 is about HV 720.6 and HV 969.7 after heat treatments at 180℃ for 2 h. The wear resistance of Ni-P plated magnesium alloy specimens is about 5 to 9 times as high as that of bare magnesium alloys.